Fog installation light wire

Cutting of air dam or front bumper cover my be required for custom installations. Position the lamps at an equal distance from the center of the vehicle and as far apart as possible. Make sure the auxiliary lamps do not restrict coolant airflow to the radiator or obstruct the factory headlamps, turn signals, or marker lamps of your vehicle.

Consult your local and state regulations regarding minimum and maximum mounting height above the ground or specific lighting requirements. Note: This is a general wiring diagram for automotive applications.

Use as reference only. Your lamp kit harness my have different wire colors. This hook up does away with the headlight lamp connection. Loosen the stud or bolts securing the fog or driving lamp to the bracket to adjust the lights up or down.

Loosen the mounting bolts to the vehicle to adjust the lights left and right. Position the vehicle on a flat surface at a distance of 25 feet 7. Measure the distance from the center of the lamp to the ground and mark off the same height on the wall.

For Fog Lamps, adjust them so the top of the light beam is 4 inches mm below the center line mark on the wall. For Driving Lamps, adjust them so the bright spot of the beam pattern is on the centerline mark on the wall. Automotive Accessories Connection. There are three main types of bulbs available for fog lights.

Pick the style that you find most useful. Environmental Protection Agency and Department of Energy focused on educating consumers about energy efficiency Go to source They also use less energy and are not as prone to vibration. The downside is their cost, as they are quite a bit more expensive than halogens.

HIDs are popular because the light produced is closer to daytime light. Halogen is the oldest type of light, but also the most widely available and cheapest to obtain.

It is made with a single filament bulb and halogen gas. These lights typically run hot and are prone to burnouts. Choose the style of lights. There are a large variety of fog light styles available, but they all break down into three mounting categories. Decide which style fits your vehicle best. Bumper Mount.

Bumper mount lights fit in specifically designed holes and are usually round or rectangular. This style is the way that most fog lights come from the factory. Grill Mount. Larger, usually round. These lights are installed on the front grille or mounted directly behind it.

This style is typically seen more with trucks and SUVs. Rack Mount. Round or rectangular lights. These are mounted above the vehicle or onto a front brush guard. This style is also seen more with trucks and SUVs. Method 2. Make sure your vehicle is parked and turned off.

Try to have it on as level a surface as possible. Engage the parking brake. Open the hood. Bumper mounted fog lights are typically below the headlights. Check your vehicle manual if you have difficulty locating them.

Disconnect the fog light switch from the housing. It should disconnect by detaching the clip. Remove the washer, bolt, and nut.

This will allow you to remove the fog light housing. Make sure that you hold on to all your parts until the installation is complete. Remove the housing. Be careful not to scratch the bumper. If you are installing grille or roof-mounted lights, lift away from the vehicle to be sure to avoid scratching the roof or body.

Insert the new fog light. The housing should fit into the space left by the old one. If it does not, you may have purchased the incorrect headlights. Make sure that the bolt holes line up; otherwise you may have to drill new ones. Insert the bolt. Thread the washer and nut over the bolt, tightening with a ratchet or wrench. Do not over tighten as you may damage the fog light housing or the vehicle. The housing should be snug and immobile.

Reattach the switch. Reconnect the fog light switch using the clip. Start the ignition. Test your new lights. Yes No. Not Helpful 8 Helpful Zipties and electrical conduit. Pay attention and don't let slack fall onto the radiator, fans, belts, or the engine itself. Not Helpful 0 Helpful 3. How do I install exterior accent lights on a Volkswagen Jetta where the fog lights go? You'll need, a Dremel to cut out the holes on the front bumper to be able to mount the lights underneath, and extra wiring connections to tie the lights into your existing electrical system.

As an added idea, consider adding an extra set on the bottom of the rear bumper to aid in backing up at night. Not Helpful 0 Helpful 1. Pull out the old one and take it to an auto parts store, they will know what to sell you. Make sure to replace in pairs, and tell them that they need to be street legal -- fog lights use special bulbs that are physically similar to, but can be made very powerful, and are designed for off-road use on vehicles like jeeps.