Install bathroom tissue holder

The advantage of ceramic bars is that they do not require any screws during installation. Instead, adhesive is applied to the back of the ceramic posts where they attach to the wall. Once the post is set in place, the adhesive secures the towel bar to the wall. A glued-on recessed holder is removed by cutting the caulking around it with a utility knife and prying it out.

If the holder is not mounted with screws or glued to the wall, it is held in place with a flexible mounting bracket. Tile-Mounted Toothbrush Holders First, attempt to soften the grout by blowing on the edges with a hair dryer on its highest and hottest setting.

You may then be able to use a putty knife to remove the grout. Try sliding the knife directly under the grout line to begin to peel it up. This is probably the most commonly used method of hanging up frames, canvases, and any other decor without leaving a trace on the wall.

Command Hooks. Hang Art From Your Molding. Use Your Mantle. Take Up Space on Bookshelves. Embrace the Wall Lean. Put the Art on an Easel. Clip it Up. Hanging pictures on tiles with adhesive tape or hanging strips. Simple double-sided adhesive tape can be a good, simple and above all a very quick solution. With a double-sided adhesive tape you can hang small, lighter pictures securely and firmly on your wall without drilling a hole into the tile.

Measure and mark the walls where you want the towel bar to go. Apply a small bead of glue to the back of the towel rack or mounting brackets and press firmly into place.

Quickly clean up any glue that has seeped out around the edges. Allow for full cure time before hanging weight on the bar. You can screw into a tile by drilling a pilot hole and using an anchor. However, you cannot put a self-threading screw into tile the same way you do with wood or sheetrock. Even if the fastener could drill through the glazed surface, the penetrating portion of the metal components would likely crack the wall.

Things You'll Need. Related Articles. Article Summary. Part 1. Choose the installation point. The installation point should also be about 26 inches 66 cm high off of the floor.

The toilet paper holder packaging should include a paper template which will help you figure where to attach the 2 brackets on your wall. Then, use a pencil to mark the places where the 2 brackets will be attached to the wall, as the template indicates. If the template is not a separate piece of paper included with the toilet paper holder, it may be printed directly on the back of the box. Measure the 4 screw locations of an installed holder before moving it.

Lift off the 2 roller holders, and measure the distance both horizontal and vertical between the 4 bracket screws. Jot the measurements down on a scrap of paper. Then, use these measurements to transfer the toilet paper holder to its new location. Replicating the measurements will ensure that the holder fits properly on the new wall.

Part 2. Mark screw locations on the wall with a felt-tip marker. Hold the bracket up in the position you outlined in pencil. Then, poke the tip of the marker through the screw hole to make a mark on the wall behind the bracket. Drill holes that are slightly smaller than the included screws.

Drill 4 holes straight into the bathroom wall, directly over each mark you made with the felt-tipped marker. For example, if the screws are each 2 inches 5. To select the correct drill bit size, pick up one of the 4 screws included with the toilet paper holder, and compare it with small drill bits. Select a drill bit that is slightly smaller than the width of the screw. Crouch down so you can look straight at the drill if necessary. Drill larger holes and insert wall anchors for added stability.

Make the hole as deep as the wall anchor is long. Then, firmly insert each anchor into a hole. Use a hammer to tap the anchors in place if needed. You can now use the wall anchors to screw the brackets into place. Plastic screw anchors are often included with new toilet paper holders. If not, you can purchase wall anchors at any local hardware store.

Part 3. Screw the brackets onto the wall. Use a screwdriver to tighten the 2 screws until both are snug. The screws will hold the bracket firmly against the wall.

You will also need to determine the correct size screwdriver to use for each screw. Estimate the best fit, and then try larger or smaller screwdrivers as necessary until you find the best fit. Hang each of the roller holders on the attached brackets.

Look at the base of each roller holder: it should be marked with an up-arrow or other visual indicator to show which side goes up. The roller holder will also have 2 slots that will slide onto the brackets. Press each roller holder down into place, 1 on each bracket. If your toilet paper holder did not come with 2 set screws, you can skip the next step. Screw 1 set screw in the bottom of each roller holder. Some roller holders have 1 screw hole in the bottom.

If this is the case with yours, screw 1 set screw into this hole. The set screw will clamp the roller holder against the bottom of the bracket and keep the roller holder from popping off the bracket.

Add toilet paper and the spring-loaded paper holder. Take a roll of toilet paper and slide the central cardboard tube over the paper holder. Then, squeeze both sides of the paper holder inward and position the paper holder between the two roller holders.

Release the spring loaded sides and make sure that the toilet paper rolls easily. Include your email address to get a message when this question is answered.